|
EMP-11 EPROM Universal Device Programmer Call Toll Free (***)-760-3820 Need it Fast! The EMP-11 programmer is a low-cost offering with windows Support and low voltage capability. The units small size offers extreme portability. The EMP-11 supports more than 4400 devices, including EPROMs, FLASH, 8051-style micros, Microchip PIC, and hundreds of other specialty devices. To change device families, simply change or flip anyone of the Family Modules. Relays and discrete DAC-controlled analog drivers provide power and ground connections. The EMP-11 also supports in-system-programming, via an adapter, on a number of devices. Parallel port communication means that you can connect to almost any PC. Serial ports make you set baud rates, make you assign IRQs, make you set flow control, and above all make you wait. The parallel port makes your data flow faster. Plug it in, start the software, and you're programming The EMP-11 is software activated, which eliminated the need for a power switch. We found that most people weren't programming devices every minute of every day, so they ended up unplugging their programmers and storing them away for some length of time, then plugging them in when the next firmware change was needed. So, turning on a power switch was simply an extra step; we decided to have the software power up the programmer instead. Because our technique of sending data through the parallel port is so fast, the EMP-11 needs no on-board RAM to store device data. All Programming Timing is generated on the programmer Programming can be performed faster (closer to theoretical minimums) when the electrical timing is more accurate. The EMP-11 uses hardware that we designed to generate timing - this means the EMP-11 can program faster than a programmer that generates it's timing on the PC. The EMP-11 is extremely portable; since it doesn't occupy a bus card in your PC, you can pack it up and take it with you anytime you wish. At only 1.5"x5"x8", with a 2" high power transformer, the EMP-11 fits into a briefcase or toolbox with ease. The programmer, parallel cable, transformer, and Family Modules, together weigh in at less than two pounds! The EMP-11's power requirements are 12-18 Volts @ 1 Amp, DC-60Hz AC so a battery can easily power it. If you need a programmer that can be easily used in a remote job site, the EMP-11 is it. One of the best values on the market Look around. No other company offers the combination of device support, tech support, and low prices that we do. Full static protection on every pin The EMP-11 is static-protected at the ZIF Socket, Family Module socket, parallel port, and power connector. The static protection on the parallel port also protects the parallel port on the EMP-11 from 12 volts, in case the user should accidentally plug it into a serial port. There is almost nothing to wear out on the EMP-11; no fan, not even a power switch. The only moving part on the EMP-11 is the Family Module, and that only moves when you switch device families - for instance, when you move from programming FLASH devices to Microcontrollers. Needham's Electronics service and support keeps you programming. Have a problem programming a certain device? Call us. Need support for a new device? check the device list - we may already support it! Family modules and rock-solid pin drivers The EMP-11 uses Family Modules to route power to the devices. This not only is a BIG cost saver, and lets us use a minimum number of very clean, precise pin drivers instead of designing cheap pin drivers for each pin. This translates to cleaner, more manageable waveforms, at a much lower price. The EMP-11 carries a 1 year warranty on all parts and labor, and a 30 day money-back guarantee It's case is made of tough .125" thick ABS plastic. (This is the same case as the EMP-11 - the one that survived having a Toyota 4x4 parked on it) 220v Transformers EMP-11 (In place of the standard 110v) Both 110v and 220v Transformers 44 Pin PSOP Adapter for EMP-11 Note: 44 Pin PSOP devices from different manufacturers vary slightly in their design. Three physically different sockets are needed to support these variations. 44 Pin PSOP Adapter for EMP-11 44 Pin PSOP Adapter for EMP-11 Call us for more adapter information (***)-760-3820 Family modules 01 through 04 are included with your EMP-10, for programming 8/16 bit EPROMs, 87xx Micros, and FLASH. See the device list for more info. (Emp 11 needham's ic eprom universal device programmer was posted and is owned by: Jane Roach) |
Jane.roach@chicagopartsnetwork.com (Jane Roach) for more information.