|
GENTEC American Rotary manufactures and distributes the largest selection of phase converters in the country. The GENTEC/Baldor proprietary design utilizes a custom-balanced soft start 3-phase generator with power factor correction, which ensures extremely smooth and balanced 3-phase output that is even better (and more economical) than standard utility 3-phase power. Proudly made in the USA. Rubber Isolation Mounts Sold Separately (Click the following for more information) * Integrated Custom Soft Start * GENTEC/Baldor Design Advantage * Built-in 3-wire latching motor starter * First Quality Oil Filled Capacitors Rubber Isolation Mounting Feet: Protect your phase converter investment for as little as $19.95/set. View American Rotary's online step-by-step easy installation pictorial. Please call toll free 1-(***)-743-6832 or email M.barber@chicagopartsnetwork.com for assistance. GENTEC's exclusive motor-integrated solid state soft-start is built directly into the motor/generator housing and drastically reduces inrush (starting) current by softening the initial starting torque required to spin the generator. The engineering departments at GENTEC and Baldor worked together to design a custom three phase motor generator that reduced the inrush current upon start-up. The results were so drastic - an 83% reduction - that the GENTEC/Baldor motor/generator was granted a Soft-Start rating. Back to top > GENTEC American Rotary takes pride in supporting domestic resources. While many motor manufactures have taken their production overseas, our custom phase converter generator is manufactured entirely in the United States. GENTEC American Rotary PowerGuardTM technology protects your equipment in power failure and brownouts. After power is restored, the converter will remain in the default "OFF" position until the operator re-starts the unit. This mechanism protects any equipment down stream from the converter that may not already have built-in power protection. Back to top > Each converter is balanced under load and no-load conditions to better than +/-5% which is essential for CNC applications. As the converter maintains this voltage balance, the power factor is corrected to close to unity. The corrected power factor also makes the phase converter less expensive to run, and virtually eliminates additional utility charges in most industrial and commercial areas. American Rotary's custom phase converter generator utilizes ISR (Inverter Spike Resistant) magnet wire, which virtually eliminates spikes common in CNC applications. Motors wound with ISR wire are 100 times more resistant to transient voltage spikes, high frequencies, and short rise time pulses commonly found in CNC equipment and inverters (VFD's). The use of ISR magnet wire dramatically extends the life of the motor/generator. Our sizing technicians are available 24/7 to answer your questions and assist you in sizing our phase converters to your specific equipment and application. We have also included a sizing guidelines tutorial online for your reference. GENTEC American Rotary converters are rated "Heavy-Duty" which make them ideal for instant motor reversing, tapping, and other heavily loaded and hard starting applications. Back to top > The Ultimate in Phase Converter Technology GENTEC American Rotary phase converter panels are not mounted directly to the motor/generator which allows many mounting options. The motor generator can even be mounted in a separate room or structure away from the control panel, if desired. The control panel can also be conveniently mounted alongside existing service. Back to top > American Rotary's digital Phase Perfect® solid state phase converter delivers 1% voltage balance under any load condition! This truly is the ultimate phase converter! Built-In 3-Wire Latching Motor Starter: The converter will start automatically at the touch of the "START" button and is conveniently pre-wired for remote start and time delay. Back to top > American Rotary offers a full line of UL/CSA listed phase converters. For operational safety, when the converter is powered on and the LED is illuminated, the "STOP" button is raised for quick shut-off. Back to top > Why Are GENTEC American Rotary Converters SO Quiet? GENTEC American Rotary phase converters are extremely quiet! American Rotary offers an informative article which describes the different kinds of noise associated with rotary phase converters. Find out why American Rotary phase converters are so quiet! Cost To Run = Real Power (kW) x ($/kWhour) Example: American Rotary 10HP Soft-Start CNC Balanced/All Purpose Idle Power = .89kW (unbalanced would nearly double to 1.4kW!) Cost To Run = .89kW x $.08/kWhour = $.07/hour at idle. Note: When a machine load is applied to the converter, the idle power shifts slightly, but is considered insignificant. American Rotary units also have corrected power factor, which keeps the amount of current that the power company has to produce to power the converter to a minimum. A corrected power factor also makes the phase converter less expensive to run in industrial areas where in addition to "real power" demand charges can occur. American Rotary's proprietary soft-start generator typically eliminates demand charges. More About Soft-Start > Since 1991, GENTEC American Rotary has led the industry in innovation and design. The company is an active member of the Better Business Bureau and strictly adheres to Truth in Advertising, ethics, and privacy standards. GENTEC phase converters are capable of running multiple motor loads, only limited by the current available. They are not limited to 3X's the rated horsepower as long as the converter is sized for starting the largest load. Please contact our technical support line for assistance toll free at 1-888-7GENTEC. Because every GENTEC American Rotary phase converter is balanced from a no-load condition, there is no minimum as to the size of a motor that can safely be run with any of our rotary converters. For example, a 2HP mill can safely run on our 40HP phase converter and still maintain a properly balanced voltage. Back to top > The GENTEC/Baldor Design Advantage Two industry leaders: GENTEC - the leading OEM phase converter manufacturer, and Baldor Electric - one of the most respected and well-known motor manufacturers in the world, have come together to design the ultimate in rotary phase converters. Our custom Baldor phase converter generator with integrated soft start and power factor correction took more than a year to develop and was designed specifically for phase converter applications and use. Back to top > GENTEC American Rotary manufactures and distributes the largest selection of phase converters online? (Isolation Mounts Sold Separately) All photography herein is protected and may not be altered or duplicated. Copyright 2007 GENTEC American Rotary Summary of My Selling Policies American Rotary is open for business every day of the year. Toll Free Technical Support is available 24 hours a day, 7 days a week. The general sales office is open Monday-Sunday from 6am-10pm cst. All phone calls are routed from our toll free number 1-(***)-743-6832. For immediate service, please call. Emails may take up to 24 hours to answer. Read my policies on my summary (40 hp cnc rotary phase converter air compressor hoist was posted and is owned by: Marva Barber) |
M.barber@chicagopartsnetwork.com (Marva Barber) for more information.
